[Mesa-users] MESA test suite 1M_pre_ms_to_wd

[sinta ayu sakinah]

Thank you for your suggestions, now I will try to run for Z=0.03 firstly,
actually I want to get the profile for metallicity Vs lifetime for the sun.
In mesa code is there any direct command for plotting metallicity vs
lifetime of the star?
Or I should run every range of metallicity one by one?

On Fri, Feb 19, 2021, 1:21 PM Natalia Dunina-Barkovskaya <ndunina at gmail.com>
wrote:

> Thank you Matteo!
>  It was not my inlist, the inlist was sent by Sinta Ayu Sakinah, but your
> advice looks very reasonable.
> Best regards to all developers and users,
> Natalia
>
> пт, 19 февр. 2021 г., 06:10 Matteo Cantiello <matteo.cantiello at gmail.com>:
>
>> Hi Natalia,
>> As you said in your email, MESA is stopping because:
>>
>> stop because model_number >= max_model_number.
>>
>>
>> Your inlist has
>>
>> max_model_number = 200
>>
>>
>> so MESA is only running for 200 timesteps. You want to increase this
>> number to a larger value.
>> Best,
>> -M
>>
>>
>> --
>> Matteo Cantiello - https://www.stellarphysics.org/
>> Associate Research Scientist,  CCA, Flatiron Institute
>> Visiting Associate Researcher, Princeton University
>>
>>
>> On Thu, Feb 18, 2021 at 7:01 PM Natalia Dunina-Barkovskaya via Mesa-users
>> <mesa-users at lists.mesastar.org> wrote:
>>
>>> Good morning! Have you tried Z=0.03? Maybe 0.04 is too much for the WD
>>> evolution...
>>>
>>> пт, 19 февр. 2021 г., 04:57 sinta ayu sakinah via Mesa-users <
>>> mesa-users at lists.mesastar.org>:
>>>
>>>> Dear Mesa Developer,
>>>>
>>>> Good morning
>>>> My name is Sinta Ayu Sakinah, i am from Indonesia, I have some trouble
>>>> when running mesa test suite 1M_pre_ms_to_wd, i want to change the
>>>> metallicity to be higher than Z=0.02d0, I used Z=0.04d0, but it didn't end
>>>> until the evolution reach white dwarf. and the reason it stops because
>>>> stop because model_number >= max_model_number.
>>>>
>>>>
>>>> this is the inlist_start
>>>> &controls
>>>>
>>>>    ! run for a few models after create pre ms, then save starting.mod
>>>>
>>>>       use_gold_tolerances = .true.
>>>>
>>>>       ! check for retries and backups as part of test_suite
>>>>          max_number_backups = 0
>>>>          max_number_retries = 15
>>>>          max_model_number = 200
>>>>
>>>>       ! stop when the luminosity has decreased to 10 Lsun
>>>>       ! for a 1 Msun star, this is roughly the on birthline
>>>>       log_L_lower_limit = 1
>>>>
>>>>       initial_mass = 1.0
>>>>       initial_z = 0.04d0
>>>>
>>>>       use_Type2_opacities = .true.
>>>>       Zbase = 0.04d0
>>>>
>>>>       varcontrol_target = 1d-3
>>>>
>>>>       photo_interval = 50
>>>>       profile_interval = 50
>>>>       history_interval = 10
>>>>       terminal_interval = 10
>>>>       write_header_frequency = 10
>>>>
>>>>       !photo_interval = 1
>>>>       !profile_interval = 1
>>>>       !terminal_interval = 1
>>>>       !history_interval = 1
>>>>
>>>> i already changed the Z to 0.04d0 for inlist_to_end_agb and for
>>>> inlist_to_wd too.
>>>> but i only got the model stops until here (picture)
>>>>
>>>> do you have any suggestion?
>>>> for the information: I trun MESA version 12778 linux ubuntu and using
>>>> MESASDK
>>>>
>>>> thank you very much,
>>>>
>>>> best regards,
>>>> sinta
>>>>
>>>>
>>>> _______________________________________________
>>>> mesa-users at lists.mesastar.org
>>>> https://lists.mesastar.org/mailman/listinfo/mesa-users
>>>>
>>>> _______________________________________________
>>> mesa-users at lists.mesastar.org
>>> https://lists.mesastar.org/mailman/listinfo/mesa-users
>>>
>>>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.mesastar.org/pipermail/mesa-users/attachments/20210219/93b523be/attachment.htm>