[Mesa-users] MESA test suite 1M_pre_ms_to_wd

[Natalia Dunina-Barkovskaya]

Thank you Matteo!
 It was not my inlist, the inlist was sent by Sinta Ayu Sakinah, but your
advice looks very reasonable.
Best regards to all developers and users,
Natalia

пт, 19 февр. 2021 г., 06:10 Matteo Cantiello <matteo.cantiello at gmail.com>:

> Hi Natalia,
> As you said in your email, MESA is stopping because:
>
> stop because model_number >= max_model_number.
>
>
> Your inlist has
>
> max_model_number = 200
>
>
> so MESA is only running for 200 timesteps. You want to increase this
> number to a larger value.
> Best,
> -M
>
>
> --
> Matteo Cantiello - https://www.stellarphysics.org/
> Associate Research Scientist,  CCA, Flatiron Institute
> Visiting Associate Researcher, Princeton University
>
>
> On Thu, Feb 18, 2021 at 7:01 PM Natalia Dunina-Barkovskaya via Mesa-users <
> mesa-users at lists.mesastar.org> wrote:
>
>> Good morning! Have you tried Z=0.03? Maybe 0.04 is too much for the WD
>> evolution...
>>
>> пт, 19 февр. 2021 г., 04:57 sinta ayu sakinah via Mesa-users <
>> mesa-users at lists.mesastar.org>:
>>
>>> Dear Mesa Developer,
>>>
>>> Good morning
>>> My name is Sinta Ayu Sakinah, i am from Indonesia, I have some trouble
>>> when running mesa test suite 1M_pre_ms_to_wd, i want to change the
>>> metallicity to be higher than Z=0.02d0, I used Z=0.04d0, but it didn't end
>>> until the evolution reach white dwarf. and the reason it stops because
>>> stop because model_number >= max_model_number.
>>>
>>>
>>> this is the inlist_start
>>> &controls
>>>
>>>    ! run for a few models after create pre ms, then save starting.mod
>>>
>>>       use_gold_tolerances = .true.
>>>
>>>       ! check for retries and backups as part of test_suite
>>>          max_number_backups = 0
>>>          max_number_retries = 15
>>>          max_model_number = 200
>>>
>>>       ! stop when the luminosity has decreased to 10 Lsun
>>>       ! for a 1 Msun star, this is roughly the on birthline
>>>       log_L_lower_limit = 1
>>>
>>>       initial_mass = 1.0
>>>       initial_z = 0.04d0
>>>
>>>       use_Type2_opacities = .true.
>>>       Zbase = 0.04d0
>>>
>>>       varcontrol_target = 1d-3
>>>
>>>       photo_interval = 50
>>>       profile_interval = 50
>>>       history_interval = 10
>>>       terminal_interval = 10
>>>       write_header_frequency = 10
>>>
>>>       !photo_interval = 1
>>>       !profile_interval = 1
>>>       !terminal_interval = 1
>>>       !history_interval = 1
>>>
>>> i already changed the Z to 0.04d0 for inlist_to_end_agb and for
>>> inlist_to_wd too.
>>> but i only got the model stops until here (picture)
>>>
>>> do you have any suggestion?
>>> for the information: I trun MESA version 12778 linux ubuntu and using
>>> MESASDK
>>>
>>> thank you very much,
>>>
>>> best regards,
>>> sinta
>>>
>>>
>>> _______________________________________________
>>> mesa-users at lists.mesastar.org
>>> https://lists.mesastar.org/mailman/listinfo/mesa-users
>>>
>>> _______________________________________________
>> mesa-users at lists.mesastar.org
>> https://lists.mesastar.org/mailman/listinfo/mesa-users
>>
>>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.mesastar.org/pipermail/mesa-users/attachments/20210219/e29a053f/attachment.htm>