[Mesa-users] MESA error: STOP bad glist for get_glist_results

[Iñigo Muñoz Elorza]

Hi again,

>How many steps would it work for? the default history_interval output is
every 5 steps, so if it only lasted 5 steps then the problem would be just
when we are doing the history output.

Not sure if I'm interpreting something wrong here, but the model will run
for several 1000s steps (the same did the other models I was referring to
with the "vmag_tables_Adrian.dat" file).

Cheers,
Iñigo

El mar., 28 may. 2019 a las 20:25, Rob Farmer (<r.j.farmer at uva.nl>)
escribió:

> Hi
> >But interestingly enough I could run several models with the
> vmag_tables_Adrian colors and the same version in the past. Why is it
> giving problems only now?
>
> How many steps would it work for? the default history_interval output is
> every 5 steps, so if it only lasted 5 steps then the problem would be just
> when we are doing the history output.
>
> Rob
>
>
> On Tue, 28 May 2019 at 10:57, Iñigo Muñoz Elorza <imunozelorza at gmail.com>
> wrote:
>
>> Hi Aaron, Rob
>>
>> Thanks for the quick answers. With Aaron's suggestion I found in the star
>> file that there was a problem with the colors module (thanks for the
>> confirmation Rob!), so now I'm running a model for 0.60 Msun but with the
>> default colors (removed the input to use the vmag_tables_Adrian.dat file,
>> which I attach).
>>
>> I also forgot to mention the MESA version, sorry, it's *r10398*. But
>> interestingly enough I could run several models with the vmag_tables_Adrian
>> colors and the same version in the past. Why is it giving problems only now?
>>
>> Many thanks!
>> Iñigo
>>
>>
>> El mar., 28 may. 2019 a las 19:43, Rob Farmer (<r.j.farmer at uva.nl>)
>> escribió:
>>
>>> hi
>>> >"STOP bad glist for get_glist_results"
>>>
>>> Is a problem in the colors module that you shouldn't hit. Can you send
>>> your "vmag_tables_Adrian.dat" file as well as your history_columns.list
>>> file. Also what version of mesa are you using?
>>>
>>> Thanks
>>> Rob
>>>
>>> On Tue, 28 May 2019 at 10:35, Aaron Dotter via Mesa-users <
>>> mesa-users at lists.mesastar.org> wrote:
>>>
>>>> Hi Iñigo,
>>>>
>>>> Try this:
>>>>
>>>> grep glist mesa/*/*/*
>>>>
>>>> Be patient and you'll see where the problem is.  From there, I bet you
>>>> can figure out what is the problem.
>>>>
>>>> Cheers,
>>>> Aaron
>>>>
>>>> On Tue, May 28, 2019 at 1:29 PM Iñigo Muñoz Elorza via Mesa-users <
>>>> mesa-users at lists.mesastar.org> wrote:
>>>>
>>>>> Hi MESA community,
>>>>>
>>>>> I want to calculate an interval of isochrones (and from there the
>>>>> luminosity functions) between 10 and 14 Gys for stars of low mass up to the
>>>>> RGB tip.
>>>>>
>>>>> For that I'm trying to compute model from 0.60 to 0.78 Msun with a 0.2
>>>>> increment, but I'm encountering convergence problems for the lower masses
>>>>> 0.60-0.66 (didn't try the higher mass yet) because either I reach a too
>>>>> small time step (*"stopping because of problems dt <
>>>>> min_timestep_limit")* or mainly because after several attempts to
>>>>> converge reducing the log10(dt/yr) and log10(dt) it stops with the
>>>>> following message:
>>>>>
>>>>> *"STOP bad glist for get_glist_results"*
>>>>>
>>>>> Any ideas of 1) what is the possible cause and 2) how to overcome it?
>>>>> Any comment or hint would be really appreciated since I didn't find
>>>>> references to the *get_glist_results.*
>>>>>
>>>>> Attached the inlist with the star_job and controls inputs (for a 0.60
>>>>> Msun star).
>>>>>
>>>>> Many thanks in advance for your help!
>>>>>
>>>>> Cheers,
>>>>> Iñigo
>>>>> _______________________________________________
>>>>> mesa-users at lists.mesastar.org
>>>>> https://lists.mesastar.org/mailman/listinfo/mesa-users
>>>>>
>>>>> _______________________________________________
>>>> mesa-users at lists.mesastar.org
>>>> https://lists.mesastar.org/mailman/listinfo/mesa-users
>>>>
>>>>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.mesastar.org/pipermail/mesa-users/attachments/20190528/4dc95af1/attachment.html>